Skc 225-380 Parallel Particle Impactor Uživatelský manuál stáhnout pdf

SKC Re-usable Parallel Particle Impactors (PPI)

The patented

†

impaction-based SKC Re-usable Parallel Particle

Impactor (PPI ) Samplers are designed to match precisely the

collection eﬃ ciency curves for respirable and thoracic dust

speciﬁ ed by ISO/CEN 7708:1995 and adopted by ACGIH,

CEN, and other occupational hygiene organizations. The

performance of the respirable PPI samplers also meets

the speciﬁ cations in the 2013 OSHA Notice of Proposed

Rule Making (NPRM) for respirable crystalline silica. The

thoracic model meets the requirements of NIOSH Method

5524 for metalworking ﬂ uids and compounds with ACGIH

thoracic TLV

s. Constructed of conductive aluminum, these

PPI Samplers may be re-used and oﬀ er a choice of ﬂ ow rates

for maximum ﬂ exibility in pump options, sample duration,

and contaminant concentration.

Performance Proﬁ le

Sampling Rate: 2 L/min respirable or thoracic and 8 L/min

respirable

Sample Pump: • Universal or AirChek

Series for 2 L/min

• Leland Legacy for 8 L/min

Sample Time: Dependent on method used

Sample Media: 37-mm PVC ﬁ lter, 5.0-μm pore size or

37-mm PTFE ﬁ lter,* 2.0-μm pore size (NIOSH 5524) or

37-mm MCE ﬁ lter, 0.8-μm pore size

Use cellulose pad or stainless steel screen for support.

Impaction

Substrate: Four 3/8-in diameter pre-oiled porous plastic discs, limited shelf-life

Analysis: Gravimetric or chemical

Body Material: Conductive aluminum

Dimensions:

Height: 4.25 in (10.8 cm) - clip to exhaust

Diameter: 1.8 in (4.6 cm)

Depth: 1.2 in (3.0 cm)

Weight: 3.3 oz (93.6 gm)

† U.S. Patent No. 7,073,402

* Back pressure on PTFE ﬁ lters can vary within the same lot.

Operating Instructions

863 Valley View Road, Eighty Four, PA 15330 USA

Tel: 724-941-9701 Fax: 724-941-1369 e-mail: [email protected]

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Operating Instructions

1SKC Re-usable Parallel Particle Impactors (PPI)The patented† impaction-based SKC Re-usable Parallel Particle Impactor (PPI ) Samplers are designed to

Strany 2 - Media Preparation

2Principle of OperationSKC Re-usable PPI Samplers are impaction-based ﬁ lter samplers that perform precise size-selection for either thoracic or resp

Strany 3 - Technical Tidbits:

34. Using forceps, insert a 37-mm support pad and a 37-mm collection ﬁ lter into the base plate.Inserting Impaction Substrates into the PPI1. Ensure

Strany 4 - Calibration and Sampling

4Calibration and SamplingAs the particle load on the ﬁ lter increases during sampling, the pressure drop will also increase. Therefore, use a compensa

Strany 5

53. Calibrate the sample pump to the speciﬁ ed ﬂ ow rate. See sample pump and calibrator operating instructions.4. Disconnect tubing and remove cali

Strany 6

6Removing the Collection Filter and Impaction Substrates1. Unscrew and remove the two screws that hold the inlet plate to the base plate.2. Li oﬀ

Strany 7 - References

7CleaningFor optimum performance, the PPI inlet, impaction, and base plates should be cleaned a er ﬁ ve runs or upon a noticeable buildup of material

Strany 8 - Ordering Information

8Ordering InformationPPI Samplers, require ﬁ lter, substrates, and support Cat. No.Respirable PPI (gold), 2 L/min 225-380Thoracic PPI (blue), 2 L/m